$36.70 |
14% OFF Phone Price : $42.70
CONFIRM THE PART FITS
Part Information
This surface element control switch (part number WP3149404) is for ranges.
Surface element control switch WP3149404 turns the surface element on and off and controls how much heat the element produces.
Unplug the range or shut off the house circuit breaker for the range before installing this part. Wear work gloves to protect your hands.
Frequently Used Together
- $63.34 |9% OFF Phone Price : $69.34
- $65.03 |8% OFF Phone Price : $71.03
- $50.48 |11% OFF Phone Price : $56.48
- $102.34 |10% OFF Phone Price : $114.34
- $97.90 |11% OFF Phone Price : $109.90
- $6.60 |13% OFF Phone Price : $7.60
- $4.39 |19% OFF Phone Price : $5.39
- $85.00 |7% OFF Phone Price : $91.00
- $67.22 |10% OFF Was : $74.69
Top models using the same part
| Model Name | Model Number | Diagram Name |
|---|---|---|
| Model #RF110AXSQ0 Whirlpool electric range | RF110AXSQ0 | Control panel parts |
| Model #RF3020XKT4 Whirlpool electric range | RF3020XKT4 | Control panel parts |
| Model #RF3020XKQ2 Whirlpool electric range | RF3020XKQ2 | Control panel parts |
| Model #RF3020XKT3 Whirlpool electric range | RF3020XKT3 | Control panel parts |
| Model #RF110AXST0 Whirlpool electric range | RF110AXST0 | Control panel parts |
| Model #RF3020XKQ1 Whirlpool electric range | RF3020XKQ1 | Control panel parts |
| Model #RF3020XKQ4 Whirlpool electric range | RF3020XKQ4 | Control panel parts |
| Model #RF3020XKT2 Whirlpool electric range | RF3020XKT2 | Control panel parts |
| Model #FEP310KN1 Roper electric range | FEP310KN1 | Control panel parts |
| Model #FEP310KV3 Roper electric range | FEP310KV3 | Control panel parts |
Reviews
WHIRLPOOL - Range Surface Element Control Switch
Took a while to receive, only minutes to install. New knob sets a bit proud when compared to the others but, it works as it should. Happy the repair part is still available.
none, Montana
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- Less than 30 minutes
Yes, I would recommend this to a friend
Easy to install surface element control
Took less than 20 minutes to install. Turn off the breaker for the range and pulled range out from between cabinets. There are about 10 hex head screws that hold the back cover on. Remove these screws with a 5/16' nut driver. Remove cover by pulling out on the bottom and then tilt out from the top. Simply pull the knob off the element control switch to the 2 Phillips tip screws that hold the element control switch in place. Remove these 2 screws and pull the control switch out the back. There are several wire set in two different connectors. Remove them one at a time and then install it on the new control before removing the other wire connector. Remove second connector and install it on the new control. These connectors will only go on one way and if you install them the way as I've just described above you can't mess up. Re-install controller through the back panel, install the two Phillips head screws that hold it in place, push the knob back onto the controller, install the back cover by tilting it in under the top flange and then tilt it down to line up screw holes, install the ten 5/16' hex head screws, slide range back in place, turn breaker on, and your finished.
Raboo, Odenville,Al
2 people thought this review was helpful.
- Ease of Installation
- Very Easy
- Duration of Installation
- Less than 30 minutes
Easy to install.
I am a female and I found this very easy to install by myself.
LaVonne, Minnesota
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- 30 minutes - 1 hour
Easy to install
Was easy to do took 15 minutes and easy to understand
Stephens 6, Watertown SD
Did you find this review helpful?
- Ease of Installation
- Very Easy
- Duration of Installation
- 30 minutes - 1 hour